loading

Wedone Group offers turnkey hot-dip galvanizing plants and automated solutions

Designing For Easy Access During Major Maintenance And Pot Replacement

Introduction

Hot-dip galvanizing is a mature yet technically demanding process. The molten zinc kettle, furnace, pretreatment line, and material handling systems form an interdependent process train: a maintenance intervention in any single subsystem can idle the entire production line. Design decisions made during early engineeringclearance allocations, component modularity, condition monitoring provisions, and access routingdetermine whether maintenance becomes a scheduled, controlled event or an emergency response with unplanned production losses.


1 The Cost of Inadequate Maintenance Access

Consider a typical scenario: a failed furnace burner on a 3-tonne-per-hour galvanizing line. With poor access design, burner replacement requires furnace cool-down (4 hours), burner removal from a confined space (2 hours), replacement installation (1.5 hours), and reheat (3 hours)a total of 10.5 hours of downtime. At an estimated production loss of $2,000 per hour plus labor, a single event may cost more than $23,000. With good access designquick-release connections, modular burner arrangement, ergonomic platforms, and an isolatable fuel trainthe same replacement can be completed in 2.5 hours at a cost of approximately $5,400. This 75% reduction in maintenance time illustrates the economic imperative of designing for maintenance from the outset.


2 Purpose and Scope

This article consolidates technical guidance for design engineers, facility managers, and project stakeholders. It emphasizes five measurable outcomes:

  1. Safe accesspersonnel can reach all serviceable components without confined-space entry or hazardous positioning.
  2. Fast interventionfailed components can be isolated, removed, and replaced with minimum line downtime.
  3. Thermal efficiencyinsulation, burner, and heat-recovery systems are maintainable without degrading performance.
  4. Environmental complianceemissions and effluent monitoring points are accessible, and containment systems are inspectable.
  5. Measurable performancekey performance indicators (KPIs) track maintenance effectiveness and feed continuous improvement.

The recommendations provide a baseline framework adaptable to site-specific constraints, local codes, and original equipment manufacturer (OEM) requirements. Where quantitative targets are given, they represent industry-derived starting values to be confirmed against project-specific conditions, local regulations, and OEM documentation.


Maintenance Readiness Levels

Maintenance readiness is assessed across four progressive levels. The design objective is to achieve Level 3 or Level 4 before commissioning, not after years of operational retrofits. Each level is defined by measurable characteristics, as summarized in Table 1.

Table 1. Maintenance Readiness Levels

Reaching Level 3 or Level 4 requires explicit design provisions from the outset. Retrofitting access platforms, adding monitoring points, or modifying insulation systems after commissioning is disproportionately expensive and often disruptive. For example, a permanently installed platform around a kettle that costs 23% of the kettle investment when designed in from the start may require 58% of the original investment when retrofittedand involves a production shutdown to install.


Core Design Principles for Maintenance Accessibility

1 Zinc Kettle Design and Access

The zinc kettle is the process core. It must maintain uniform molten zinc temperature while permitting inspection, heating element service, and eventual replacement or repair.

Recommended design provisions:

  • Clearance zones: Provide a minimum working clearance of 1,0001,200 mm around all serviceable kettle surfaces, subject to local codes and OEM specifications. This allows personnel access, lifting equipment maneuverability, and removal of replaceable sections. The larger dimension (1,200 mm) is preferred where mobile equipment or high-temperature work is anticipated.
  • Modular construction: Specify removable side panels or modular kettle sections to enable targeted internal inspection and sectional repair without full kettle extraction. Section-based replacement reduces material cost, transport logistics, and downtime compared with full kettle replacement. Modular designs require careful welding procedures per ASTM A385 and must maintain structural integrity under thermal cycling. Warpage prevention per ASTM A384 should guide kettle shell and support structure design.
  • Lifting provisions: Integrate lifting lugs and jacking points rated for the heaviest replaceable section. Document capacities in the operation and maintenance (O&M) manual. Include provisions for external lifting beams or gantries where mobile cranes cannot access the area.
  • Elevated access platforms: Install platforms around the kettle rim and heating element zones with guardrails, non-slip flooring, and compliant egress per OSHA 29 CFR 1910 Subpart D. Platform design must accommodate both routine inspection and emergency egress. Stair access is preferred over ladders for platforms used daily; vertical ladders should be limited to emergency-only or infrequent inspection routes.
  • Insulation design: Specify insulation systems that can be removed and reinstalled without damaging the kettle shell. Use reusable insulation blankets or interlocking panels where feasible. Avoid permanent refractory castings where regular access is needed; instead, design removable panels with mechanical fasteners.
  • Thermal monitoring: Install multiple thermocouples at different depths and positions to verify temperature uniformity and detect localized hot spots indicative of refractory degradation or zinc buildup. Digital readouts at a central control panel eliminate the need to approach the kettle during normal operations.
  • Thickness monitoring: Implement scheduled ultrasonic thickness measurements at documented grid points. Compare readings against baseline commissioning data to track wall thinning from corrosion and erosion. Establish alarm thresholds at 75% of original wall thickness; schedule replacement planning when readings reach 50%.

Quantitative design target: For a standard kettle measuring 46 m in length, provide at least 810 thickness measurement points per face (sides, ends, bottom), marked with permanent location indicators.


2 Furnace Selection and Combustion System Maintenance

Furnace design directly affects burner servicing, control system access, and exhaust maintenance. Maintenance-friendly features must be specified at the equipment selection stage.

Recommended provisions:

  • Quick-release burner assemblies: Specify burners that can be isolated, removed, and replaced without dismantling the furnace shell. Use flange-mounted burners with accessible fuel and air connections. Each burner should have an independent isolation valve and a quick-disconnect coupling, enabling removal while other burners continue operating where combustion safety permits.
  • Modular burner arrangements: Arrange burners so that any single unit can be serviced while others remain operational, where combustion safety permits. Group burners in banks with independent control zones; this also improves turndown capability and operational flexibility.
  • Ergonomic control panels: Position control panel interfaces at heights between 900 mm and 1,500 mm above floor level, with clear labeling and diagnostic access to programmable logic controller (PLC) modules. Provide a diagnostic port for laptop connection without opening the panel. Graphic displays should indicate burner status, flame detection signals, and alarm history.
  • Exhaust system access: Provide removable inspection ports, cleanouts, and gas sampling points on all exhaust ductwork. Differential pressure taps on each duct section allow blockage detection from zinc oxide buildup or refractory debris. Cleanout ports should be sized to allow manual obstruction clearance or robotic crawler access, as appropriate.
  • Swing-open or removable doors: Specify furnace doors that open fully or detach completely to allow interior inspection and refractory repair. Door seals should be replaceable without removing the entire door assembly.
  • Lockout/tagout (LOTO) integration: Install LOTO points, emergency shutoffs, and secondary access ladders in accordance with OSHA 29 CFR 1910.147. Safety systems should support, not obstruct, maintenance workflows. Position LOTO points at each energy sourcegas, electrical, hydraulic, pneumaticwith clear identification. Conduct a LOTO audit before commissioning to verify that all energy sources can be isolated independently and that the isolation and restoration sequence is documented.

Furnace safety compliance: NFPA 86 and EN 746-1 establish baseline safety requirements for industrial ovens and furnaces, mandating flame detection, fuel train safety interlocks, and exhaust monitoring. Design provisions should ensure these safety components are testable from the control panel without requiring furnace shutdown.

Quantitative design target: The time to access, isolate, and remove a burner assembly for replacement should not exceed 30 minutes for a trained technician working alone.

Worked exampleburner replacement time comparison:

Poor access design: Furnace shutdown and cool-down to ambient (4 hours due to thermal mass); burner located behind fixed steelwork requiring partial furnace shell removal with cutting torches (2 hours); burner replacement requiring crane lifting and confined-space entry (2 hours); reheat to operating temperature (3 hours). Total: 10.511 hours downtime.

Good access design: Burner mounted on a hinged door with quick-release fuel and air connections; isolated and opened while adjacent burners continue firing. Physical change completed in 1.5 hours with the furnace at operating temperature; no cooldown or reheat required. Total: 2.5 hours downtime.

At $2,000/hour production loss plus $150/hour labor:

  • Poor design cost: 10.5 hours $2,000 + 10.5 hours $150 = $22,575$23,650
  • Good design cost: 2.5 hours $2,000 + 2.5 hours $150 = $5,375

This example illustrates that design provisions costing 13% of furnace capital expenditure can yield a payback period of less than 12 months through reduced downtime alone.


3 Pretreatment Systems and Environmental Compliance

The pretreatment lineincluding degreasing, pickling, rinsing, and fluxing tanksinvolves chemical handling, mist generation, and wastewater discharge. Layout decisions here significantly affect chemical exposure risk, spill containment effectiveness, and regulatory compliance.

Recommended design provisions:

  • Accessible monitoring: Install chemical level, pH, temperature, and conductivity sensors with readouts positioned outside the tank area. This allows operational supervision without requiring personnel to approach open chemical tanks. Integrate readouts into the central control system for continuous data logging.
  • Filter and mist eliminator service access: Position filters and mist eliminators so replacement can be performed from safe, ergonomic positionspreferably from walkways or platforms rather than over tank openings. Where filters are located above tank level, provide permanent service platforms with stairs rather than ladders.
  • Inspectable spill containment: Design secondary containment systems with leak detection sensors, drain valves, and clear visual access. Containment liners should be replaceable; specify liner materials compatible with the full chemical range used in the facility. Conduct annual leak testing of containment integrity.
  • Closed-loop water treatment: Evaluate closed-loop water treatment and chemical recovery systems where process conditions permit. Acid recovery via ion exchange or diffusion dialysis can extend pickle bath life by 510 times and reduce sludge generation.
  • Sampling points: Install accessible sampling ports on wastewater discharge lines and air emission ducts, positioned to allow safe sample collection by one person without scaffolding or temporary platforms. Sampling ports for hot or corrosive streams should include cooling coils or dilution provisions to protect personnel.
  • Automated alarms: Implement automated alarms for low/high chemical levels, pH excursions, and pressure drops across mist eliminators. Maintenance alerts should route to both operators and maintenance staff via a common alarm management system.

Environmental compliance approach: Air emission and wastewater discharge limits vary by jurisdiction. Design the monitoring and sampling infrastructure to local permit requirements from the outset, rather than retrofitting sampling ports after permit violations occur.


4 Material Handling and Automation Integration

Material handling equipmentcranes, hoists, conveyors, and automated guided vehicles (AGVs)must be positioned so that heavy machinery can be moved away from maintenance zones, preventing conflicts between production and service activities.

Recommended automation provisions:

  • Remote monitoring: Equip motors, gearboxes, brakes, and conveyors with remote monitoring sensors (vibration, temperature, current draw). This enables condition-based maintenance and early fault detection. Establish baseline vibration spectra at commissioning and track changes over time; an increase of 2550% from baseline warrants investigation.
  • Predictive maintenance analytics: Where feasible, integrate machine learning tools that analyze sensor data to predict component failure before it occurs. Even without machine learning, simple trend analysis of vibration and temperature data can identify developing faults weeks before failure.
  • Automated diagnostic protocols: Standardize troubleshooting sequences using PLC-based diagnostic routines. For example, a burner fault message should automatically display the sequence of diagnostic checksfuel pressure, flame detection, air flowin order, with current readings shown.
  • AGV routing flexibility: Design AGV paths that avoid permanent maintenance zones and can be dynamically rerouted during service activities. Maintain adequate aisle widths for combined AGV passage and maintenance equipment movementtypically 1,5002,000 mm.

Important caveat: Automation should not replace physical access. Even with advanced monitoring, maintenance personnel must be able to physically reach every replaceable component. Automation enhances the speed and accuracy of diagnosis but cannot substitute for direct human access.


5 Energy Efficiency and Risk Mitigation

Energy-efficient equipment reduces operational stress and can decrease maintenance frequency. Benefits include:

  • Reduced thermal cycling on the zinc kettle, which extends shell life by minimizing expansioncontraction fatigue. Stable operating conditions (temperature variation of less than 5 C across the kettle) can extend shell life by 3050%.
  • Lower energy consumption per ton of product, reducing both operating cost and environmental footprint. Energy efficiency improvements of 1020% are achievable with well-designed insulation, burner controls, and heat recovery.
  • Extended component life through stable operating conditions, reducing burnouts of heating elements, refractories, and circulating fans. A 1015 C reduction in flue gas temperature via heat recovery can extend refractory life by 2030%.

Energy monitoring requirements: Track energy consumption by process stage (kettle heating, pickling bath heating, rinse water heating, fume extraction). Compare actual performance against design specifications at least monthly. Evaluate heat recovery from furnace exhaust or kettle surfaces where technically and economically feasible; a typical recuperator can recover 2030% of exhaust heat, with payback periods of 13 years depending on fuel costs.

Risk mitigation: Better access enables more frequent inspections, which in turn allows earlier detection of emerging issueszinc leakage, refractory cracks, burner flame instability. Faster response to anomalies reduces the probability of catastrophic failures. Establish a structured inspection regime: daily operator rounds, weekly maintenance checks, and monthly comprehensive inspections, with checklists tied to specific design features.


Technical Design Considerations for Core Equipment

1 Zinc Kettle Engineering

The kettle must sustain molten zinc while enabling maintenance. Table 2 maps typical maintenance tasks to recommended design provisions.

Table 2. Typical maintenance tasks and recommended design provisions for zinc kettles

Non-destructive testing: Ultrasonic thickness gauging detects wall thinning from zinc attack and erosion. Thermal imaging identifies refractory hot spots and insulation degradation. Both methods should be performed by trained technicians and documented for trend analysis. For thermal imaging, establish clear criteria: any area with a temperature exceeding the design maximum by 15% should trigger further investigation.


2 Furnace and Combustion Systems

Furnace reliability depends on burner maintenance, combustion control, and exhaust management.

Design provisions:

  • Isolatable burner assemblies: Each burner should have independent fuel and air isolation valves, allowing removal without furnace shutdown where safety permits. This is the single most impactful design feature for reducing downtime.
  • Accessible fuel trains: Combustion air and fuel trains require accessible filters, regulators, valves, and pressure switches. Group these components on a common skid, mounted at service height (9001,500 mm above floor). Use standard fittings wherever possible to reduce the variety of spare parts required.
  • Testable safety interlocks: Flame detection and safety interlocks must be testable from the control panel. Include manual test modes for each safety function and document expected response times. Periodic interlock testing should be part of the preventive maintenance schedule.
  • Exhaust system cleanouts: Install cleanout ports at duct transitions and low points where ash, zinc oxide, or condensation can accumulate. Ports should be sized for the expected debris volume; a minimum of 300 mm 300 mm is recommended to allow rodding or vacuum access.
  • Recuperator bypass: If heat recovery is installed, include a bypass damper so the recuperator can be isolated for cleaning or replacement without furnace shutdown. Interlock the bypass damper with combustion controls to maintain safe operation during maintenance.

Preventive maintenance schedule: Table 3 provides a baseline schedule; frequencies should be adjusted based on OEM recommendations and operating experience.

Table 3. Preventive maintenance frequencies for furnace and combustion equipment


3 Pretreatment Line Design

Pretreatment line layout must balance chemical process requirements with maintenance access.

Recommendations:


  • Service aisles: Provide aisles on at least one side of all tanks, with a minimum width of 9001,200 mm. This allows access for chemical monitoring, filter replacement, and tank cleaning. The wider dimension (1,200 mm) is preferred for tanks longer than 6 m or where mobile equipment is used.
  • Grouped piping: Group and label piping by function (process chemical, rinse water, compressed air, exhaust). Use color-coded pipe markers per ANSI/ASME A13.1 where applicable. Piping routes should avoid crossing walkways and maintenance access zones where possible.
  • Skid-mounted equipment: Mount pumps, heat exchangers, and filters on removable skids for rapid replacement using a forklift or pallet jack. Each skid should have standardized connector sizes and orientations to simplify connection and reconnection.
  • Tool-less guards: Design covers and guards for removal without special toolshand knobs or quick-release clampsto reduce service time. Use safety-lockable mechanisms where required by regulation, but design for rapid opening.
  • Sampling and cleaning access: Design rinse water and flux systems with dedicated sampling points and clean-out ports. Position sampling points to obtain representative samples without requiring the operator to reach over open tanks.

4 Environmental Control and Monitoring

Environmental controls protect workers and the surrounding community. All monitoring and service points must be accessible.

Design provisions:


  • Fume extraction hoods: Size hoods for the specific process chemistry and zinc bath geometry. Monitor hood performance with differential pressure gauges that indicate filter loading or fan degradation. Establish alarm thresholds at 7080% of maximum allowable pressure drop.
  • Mist eliminators: Install pressure gauges across each mist eliminator stage. Replace filter elements when differential pressure exceeds the OEM threshold; design for replacement from floor level or a dedicated service platform. Provide a spare set of filter elements on site to minimize downtime.
  • Wastewater treatment: Provide continuous pH, flow, and conductivity monitoring with accessible probes and calibration ports. Calibrate sensors monthly, or more frequently if local conditions require. Log all calibration activities for compliance audits.
  • Spill containment: Include leak detection sensors and drain valves in all containment sumps. Design containment liners for periodic replacementtypically every 510 years depending on chemical service. Test containment integrity annually.
  • Air emission sampling ports: Position sampling ports at locations specified by the local environmental permit, ensuring safe one-person access. Provide permanent access platforms where ports are located above floor level. Seal sampling ports when not in use to prevent false readings.
  • Alarm systems: Alarm notifications should reach both control room operators and maintenance staff via a common system. Define alarm priority levels and escalation procedures in the O&M manual. A typical system has three alarm levels: informational (logged only), warning (notify operators), and critical (page maintenance staff and supervisors).

5 Material Handling and Automation Integration

Material handling systems require dedicated maintenance access:


  • Overhead cranes: Provide service platforms at crane rail level for trolley and hoist maintenance. Walkways with guardrails are mandatory. Design platforms for both regular inspection tasks and major maintenance such as brake replacement and rope or chain renewal.
  • Hoists and jigs: Design for quick changeover and inspection using quick-release fasteners where feasible. Jigs should be designed so they can be fixtured on a service stand, allowing in-place repairs rather than removal to a workshop.
  • AGV routes: Design paths to avoid permanent maintenance zones. Include rerouting capability in the control systemAGVs should automatically reduce speed and re-route when personnel enter maintenance zones via zone sensors or personnel tracking. Verify aisle widths against the largest mobile maintenance equipment.
  • Predictive maintenance sensors: Install vibration and temperature sensors on critical rotating equipment. Track current draw on motors to detect mechanical degradationa 1015% increase over baseline is cause for investigation. Route sensor data to the central maintenance dashboard.

Verification, Commissioning, and Continuous Improvement

Design-for-maintenance features must be verified before commissioning. Table 4 summarizes recommended verification methods.

Table 4. Verification methods for design-for-maintenance provisions

Factory and site acceptance testing (FAT/SAT): FAT and SAT protocols must include maintenance access checks, not just functional performance tests. Both should include a "maintenance walk-through" for key equipment, verifying that a representative technician can perform typical service tasks within the agreed time targets.

Post-commissioning key performance indicators (KPIs): Table 5 lists suggested KPIs for tracking maintenance effectiveness.

Table 5. Suggested KPIs for maintenance-effectiveness tracking

KPI reviews should feed back into design improvements for future projects and into preventive maintenance schedule adjustments for the existing plant. A quarterly review meeting should assess KPI trends, address systemic issues, and update the maintenance plan accordingly.


Contractual and Regulatory Provisions

1 Contractual Clauses

Contractual documents should specify maintenance access requirements, spare parts, training, and documentation deliverables.


  • Guaranteed clearance zones: The contractor must demonstrate that all specified clearance zones exist in the as-built installation. Establish clear measurement and verification criteria in the contract; confirm as a condition of final acceptance.
  • Spare parts list: Deliver a complete spare parts list with lead times and recommended stock levels at handover. Include both consumables (filters, seals, gaskets) and critical spares (burners, sensors, control boards). Identify alternates for single-source components where feasible.
  • FAT/SAT with maintenance walk-through: Include maintenance access checks in FAT and SAT protocols, verifying that a representative technician can perform typical service tasks within agreed time targets.
  • Training: The contractor must provide competency-based training for operators and maintenance staff on LOTO procedures, burner service, and environmental control maintenance, with practical assessments and refresher schedules. Budget a minimum of 40 hours of on-site training per discipline.
  • Deliverables: Submit as-built drawings, 3D models, and digital maintenance manuals before final acceptance. The 3D model should include maintenance access features (platforms, clearances, lifting provisions) to support future design modifications.
  • Performance guarantees: Contractual guarantees for uptime, thermal efficiency, and emissions should include maintenance-access verification as a condition of acceptance. For example, a guaranteed MTTR should be validated during the SAT maintenance walk-through.

2 Regulatory Alignment

Compliance with the standards in Table 6 is the baseline design requirement.

Table 6. Key standards and regulations referenced


Conclusion

A design-for-maintenance framework for hot-dip galvanizing plants delivers measurable improvements in uptime, safety, and equipment longevity. By targeting Level 3 or Level 4 maintenance readiness at the design stage, engineers and facility managers transition from reactive repairs to predictive, design-integrated maintenance. The practical recommendations in this articlequantified clearance zones, modular components, condition monitoring infrastructure, ergonomic access, and explicit contractual provisionsare actionable steps toward a more reliable, compliant, and efficient operation.

The framework emphasizes early-stage decisions because retrofit costs for access platforms, monitoring systems, and insulation modifications are typically 23 times higher than the incremental cost of designing them in at the outset. The worked example in Section 3.2 demonstrates a savings of more than $17,000 per burner replacement event, achieving payback in less than 12 months for modest design investments. These figures are illustrative; actual results depend on site-specific factors, production values, and labor rates. Facilities should validate all numerical targets against their own operating context before committing to design decisions.

For greenfield projects, the design parameters in Sections 3 and 4 should be incorporated into basis-of-design documents and reflected in P&IDs, general arrangement drawings, and 3D models. For existing facilities, the framework provides a structured audit methodology for prioritizing upgrades: the four readiness levels serve as a self-assessment tool, and the verification protocols in Section 5 enable measurement of progress.

Ultimately, the goal is not simply to make maintenance easierit is to make maintenance predictable, safe, and performance-transparent. When maintenance is planned around accurate condition data and executed with proper access, downtime becomes a scheduled, budgeted event rather than an operational crisis. This transformation is possible only when maintenance considerations are embedded in the design process from day one, not retrofitted after years of operational patches.


References

  1. ISO 1461, Hot dip galvanized coatings on fabricated iron and steel articlesSpecifications and test methods, International Organization for Standardization, Geneva, Switzerland.
  2. ASTM A123/A123M, *Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products

Contact Us For Any Support Now
Table of Contents
GET IN TOUCH WITH Us
recommended articles
NEWS Cases
WEDONE Completes Customized Hot-Dip Galvanizing Furnace and Zinc Kettle Package  in South Africa
On July 27, 2026, WEDONE completed the factory inspection and export preparation of a customized hot-dip galvanizing furnace and zinc kettle package. With South Africa as the target country, the project was developed around the customer's equipment interfaces, recorded dimensions and international transport requirements. It represents a coordinated equipment supply for a hot-dip galvanizing operation rather than the delivery of a single standalone component.
Key Factors to Consider When Selecting Hot-Dip Galvanizing Equipment for Steel Structures and Tubes
Looking for a trusted Hot‑Dip Galvanizing Equipment Manufacturer? Read key criteria for selecting galvanizing gear for steel tubes, strut and structural steel production.
From Blueprint to Production: What to Expect from a Turnkey Hot-Dip Galvanizing Plant Project
Learn the key stages of a turnkey hot-dip galvanizing plant project, from layout design and manufacturing to installation, commissioning and training.
Wedone Technology Safely Dispatches Advanced Zinc Kettle to Myanmar, Expanding Southeast Asian Footprint
On March 19, 2026, Shanghai Wedone Environment & Energy Technology successfully completed the factory manufacturing and secure logistical dispatch of a heavy-duty, customized zinc Kettle system bound for Myanmar. This successful delivery marks another significant milestone in Wedone’s ongoing regional expansion, reinforcing the company's commitment to delivering top-tier engineering equipment and expanding its specialized footprint across the Southeast Asian industrial market.
Visit and Friendly Exchange with the Russian International Zinc Association Delegation
Wedone Group recently welcomed a delegation from the Russian International Zinc Association to our manufacturing facility for an on-site visit and technical exchange. The delegation was given a comprehensive tour of our production workshops, engineering facilities, and quality control processes, gaining firsthand insight into our manufacturing capabilities and technological strengths in the field of hot-dip galvanizing equipment.
Wedone Technology Safely Dispatches CE-Certified Galvanizing Furnace and Control Systems to Turkey
Wedone Environment & Energy Technology successfully completed the manufacturing, strict inspection, and safe factory dispatch of a customized, high-performance galvanizing furnace and zinc pot system destined for Turkey. This successful export delivery represents a significant milestone in Wedone's continued market expansion across the Mediterranean and Eurasian metallurgical sectors, reinforcing the company's capabilities in delivering heavy-duty, large-scale industrial thermal systems on a global scale.
Keynote Speech at the 8th International Hot-Dip Galvanizing Conference & Exhibition
At the 8th International Hot-Dip Galvanizing Conference & Exhibition, Mr. Lan Tian, General Manager of Wedone Group, was invited to deliver a keynote speech, sharing insights on advanced galvanizing technologies, industry development trends, and sustainable solutions.
Wedone Technology and International Zinc Association Hold Friendly Talks at Changsha International Exhibition on Global Galvanizing Industry Import-Export Cooperation
On September 24, 2025, Wedone Environment & Energy Technology (Shanghai) Co., Ltd. participated in the Changsha International Exhibition. During the event, the company’s representatives met with Martin, President of the International Zinc Association, and held talks on the import and export of the international galvanizing industry.
A Promising Start for the Galvanizing Furnace Project in Turkey
TTM Endüstriyel is pleased to announce a strategic partnership with WEDONE Energy Technology to provide advanced engineering solutions for hot-dip galvanizing plants and equipment.This collaboration represents an important step toward expanding both companies’ capabilities in delivering high-quality industrial solutions to the global galvanizing industry.
Wedone Technology Showcases Green Thermal Solutions at Moscow Steel Structure Exhibition
From May 26 to 28, 2026, the 11th International Steel Structure Exhibition concluded at the Timiryazev Exhibition Center in Moscow, Russia. Shanghai Wedone Environment & Energy Technology was invited to participate, utilizing this elite global platform to showcase its cutting-edge industrial solutions and engage with key European and Asian stakeholders. As a premier gathering for the metallurgical and steel fabrication sectors, the Moscow exhibition attracted top-tier manufacturers, engineers, and suppliers from across the region, making it a strategic opportunity for the company to expand its global footprint.

cutting-edge galvanizing solutions

Our vision is to drive sustainable industrial progress by providing state-of-the-art technology, superior quality, and unmatched service.
Contact with us
Contact Person: LAN TIAN
Tel: +86 21 5835 6625
WhatsApp: +86 139 0195 1068
Company Address: 7th floor, Yinqiao Building, No. 58 Jinxin Road. Pudong District, Shanghai 201206, P.R. China
Customer service